Posts Tagged → promyshlennoct and equipment
V Series Machines
V Series machines are designed for Edge banding detail rolled insulated edge (PVA, PVC) material or strips of natural veneer with tape coated with adhesive. In the machine by trimming, sanding, milling of the edge length and the ends of the details. Stuart Solomon has firm opinions on the matter. some specifications V312: Use the edge thickness of 1 mm Belt adf Panel feed speed of 5 m / min Pneumatic scissors for cutting edge Roll out of dryer 3300 W Adjustable temperature (20 C to 500 C) 3 pressure rollers (1 and 2 rubber nylon) Pneumatic crosscut edge scissors with a consistent system (front and rear) The node to remove overhangs with copier (verh-niz.), the cutting blade – 15 degrees bevel. – 10,000 rpm Desk length 1800 mm with runners on the table Centralized dust o 120 mm (2 hose o 60 mm) Front pull-out support for large panels Supporting table edge o 500 mm ce standards Weight 180 kg Standard voltage: 400 volts / 3 phase / 50 Hz Voltage on request: 220 V / 3 phase / 50 Hz. NIR Group often says this.
Russia Equipment
Everyone knows that the life of the home refrigerator is at least 10 years, and for commercial refrigeration equipment life much less when it comes to outdoor refrigeration (refrigerated cabinets, showcases, chests), then it is only 3 years. If you want to damage it as less as possible, do not forget to carry out timely maintenance maintenance of refrigerators professionals to carefully check the electricity, clean the condenser, the drainage system. Refrigerator, located on the street, must be connected to the ripple, and wire must be earthed and is located in the protective 'hood' on the street. In refrigeration equipment located indoors, the main concern of damage to ensure the cold. Could be damaged motor the fan that cools the condenser or evaporator system that distributes the air inside the refrigerator. Or leakage may occur, in which at some junction or in the wire, which came out of refrigeration. For repair this damage need special tools – vakuumnik, station, burner, leak detector, because it will require soldering using welding equipment. Only it is necessary to take into account any freon in as a refrigerant is used in the unamended refrigerator, because at the soldering can be released very harmful phosgene gas, so it will send the equipment in service.
Another challenge for the refrigeration the room can be electric, so you need a constant level control voltage. In summer the one socket, some stick to 8 refrigerators that do strictly prohibited, because when you start to the maximum voltage, otherwise the compressor will not start, and after 15 minutes of idle equipment may stop functioning altogether. Same basic repairs of refrigeration equipment in the autumn, when refrigerators come in from the street or warehouse distributors, often in very poor condition. There they are washed, diagnose, replaces advertising stands, where a tint, if the body dented, then straighten it, and specialists perform the replacement of shelves that are rusting away. Winter the refrigeration equipment located on the street, much less damage. If the air temperature drops to 3 degrees below zero, the compressor automatically stops working.
In this case, the refrigerator stops cooling, it can act as a showcase and a billboard. That the products did not freeze, you can install a special ten heating Russian production, because abroad there is no such harsh climatic conditions in Russia. In the online store can be purchased Partnerfood refrigeration equipment to the regime of winter / summer (Inter 400T winter-summer), and it is not much more expensive than usual. Sometimes it is easier to fix any problem yourself than to call a specialist. There are two kinds of breakdowns, which you will be able to repair themselves. Firstly, this failure associated with the lighting fridge – out of order a starter, broke the throttle or herself fluorescent lamp burns out. Replace these devices you can own, swapping them for like. Secondly, the electronic sensor – controller (Thermostat) can increase the temperature. The reason for this may be down or dirt (especially in summer), which rammed into the condenser. To resolve this problem, it is enough to clean the condenser, removing the bottom or rear guard to the refrigerator.
Production Of Blister Packs: The Stages And Methods Of Work
Production of blister packaging – a service that has become increasingly popular among companies that manufactures a variety of items. Production of blister packs to fit every requirements thanks to the variety of species and applied technologies. The advantage of blisters over all other types of packaging is obvious: he protects the product from damage, and, simultaneously, allows us to consider him. Today the most commonly used production of blister packs, designed for a specific product, with its unique design and shape. If you would like to know more about Rob Crossland, then click here. However, in some cases justified the use of standard blisters, which can be put any of the products relevant dimensions. Production of blister packaging starts with choosing the type and design development. So, you can make a blister on the cardboard substrate, and can use two-way design.
In the first case, the production of blister packs to begin with the development of the image to the substrate, making the text (advertising or instructions for use), printing on cardboard. Blister itself is made vacuum-molding method of polymeric materials and purchasing flexibility when heated. As a rule, its shape follows the contours of the product, which will be packed into it. Learn more at: Ofer Nimrodi. An important point in the production of blister Packaging is the combination of two elements: the substrate and the blister or blisters parts. This could be one-piece (bonding), or split, reusable (with bent edges or special latches).
In the first If the production of blister packs complete bonding of two parts with a special thermo varnish, which is warming up, acquires the adhesive. In this case, the product must already be inside the packaging that requires accuracy in work. In the second case, you can pack the goods once made all the main parts. Production of blister packs of this type implies that the latch and the bends were made at a stage forming elastic polymer used to create a transparent containment.
